Hi,imam lan karta SURECOM EP-320X-S koqto ne moga da
podkaram pod linux

    Pod RedHat 7.3 ne e vkliu4ena podryjka "Myson MTD-8XX PCI
Ethernet support" i vyob6te ne mi q razpoznava!

    Mandrake 9.0 pri instalaciqta vijda 4e imam lan no ne
 moje da razbera kakva e i mi dava spisyk da mi q poso4a na
 tam nqna surecom ima realtek i tyj kato znam 4e miqta e s
 takyv 4ip mu q slagam no mi kazva 4e ne stava.Tuk v
 mandraketo proverih 4e "Myson MTD-8XX PCI Ethernet support"
 si e vkliu4en i v PCI-KDE Control Module mi dava slednata
infornaciq za kartata:
 00:09.0 Ethernet controller: MYSON Technology Inc: Unknown
device 0803
        Subsystem: Surecom Technology: Uncnown device 1320
	Flags:bus master, medium devsel, latency 32, IRQ 9
 I/O ports at a000 [size=256]
         Memory at e5800000 (32-bit, non-prefetchable)
[size=1K]
        Expansion ROM at<unassigned>[disabled][size=64K]
	Capabilities:[88]Power Managment version 2

a pyk kato napi6a: dmesg | grep eth0 ni6to ne mi vry6ta
v Network interfaces ima samo:
lo    127.0.0.1         255.0.0.0       Loopback    Up
eth0 go nqma :((

    Knoppix(toq linux deto e na CD).Kato proverq v PCI-KDE
 Control Module mi dava absoliutno sy6toto kakto pri
Mandrake-to oba4e kato napi6a: dmesg | grep eth0 
 mi vry6ta : eth0: 100/10M Ethernet PCI Adapter at 0xa000,
00:02:44:33:04:88, IRQ 9.
 posle pi6a:ifconfig eth0 192.168.192.155 netmask
255.255.248.0 broadcast 192.168.192.255 up
i v Network interfaces se poqvqva:
eth0  192.168.192.155   255.255.248.0   Broadcast   Up
lo    127.0.0.1         255.0.0.0       Loopback    Up
i kartata si ba4ka na pu6ka :)) 


Za6to ne mi ba4ka pod Mandrake??
 Ajde pod RedHat e qsno 6to -> ne e vkliu4en "Myson MTD-8XX
PCI Ethernet support". 

10x predvaritelno

mi pich kvo da ti kaja ne moa ti pomogna :)) hahaha
no moga da te posavetvam da si kupish nov lan ;o)))
 a pa ako mislish niakoga da si kachvash winXP vij vtoria
red^

Vij trqbva da imash disketa, na neq ima drivers za linux.
 Edin .c file i edno README, vyv vtoriq ima podrobni ukazaniq
kak da go kompilirash i insmod-nesh.
 LAN-kartata s mnogo qka, lichno predpochitam RealTek .. no
pyk 3128 imat problemi pri bridge mode. i taka ..
kakto i da e, vij disketata.

v readme-to pi6e da razre6a "Myson MTD-8XX PCI
Ethernet support" :

If your Linux kernel is any new version above than 2.4.5
Enable the option of "Myson MTD-8XX PCI Ethernet support"
  in "Ethernet (10 or 100 M bit)" of "Network device support"
as a loadable module or system default module.

 Tova e napraveno po default o6te pri samata instalaciq v
Mandrake 9.0

OK moje i da greshq, tova sym go digal predi 5-6mes.
 i vse pak trqbva da ima .c file .. stoto sym 100% siguren
che ne sym go dyrpal ot net.
 Pyk ako nqma .. razrovi se iz source-to na nqkoi po-star
kernel vzemi C faila i si go kompilirai :)
 A inyche za da ba4ka kartata trqbva da e na MODUL, ne
vgraden v kernel-a.

 Zdravej pak Anonymous.Na disketata s drajverite v dir LINUX
 i mam Readme.txt i edin dir "2.2.X" v kojto v edin *.tar sa
slednite dailove:
kern_compat.h
pci-scan.h
pci-scan.c
mtd80x.c
Makefile
Az sym s kernel 2.4.19 t.e popadam v 4 to4ka ot Readme-to.
A pyk Readme-to e slednoto :


 *******   This document contains instructions on Linux
driver installation for   *******
 *******           SURECOM EP-320X-S/S-1 100/10M Ethernet PCI
Adapter             *******

     The Linux driver for Myson MDT8xx compatible MAC chipset
on
  this adapter has been embedded into Linux systems since
kernel
  version 2.4.5, and this makes this adapter automatically
detected
 and installed with the driver supported by Linux system.

    Therefore,

     1. If your Linux kernel is still old version 2.2.x,
please use
 and refer the driver supported for kernel version 2.2.x in
 \Linux\2.2.x directory on the driver diskette.


     2. If your Linux kernel is version 2.4.x previous than
version
  2.4.5, please get the latest kernel file from the web site
of The
  Linux Kernel Archives (http://www.kernel.org/). Then,
install and
  re-compile the downloaded latest kernel file into your
current
 Linux system.


     3. If your Linux kernel is or has been patched to
version
  above 2.4.5 but you have not enabled or configured the
MTD8xx
  compatible driver as dynamic loadable or embedded system
module,
 then you could follow the step 4 to enable the driver and
 re-compile the kernel.

        If you could use the console command "#locate
fealnx.o" to
  locate the module driver file or find the driver module
file
  fealnx.o in kernel source /usr/src/linux-2.4.x/drivers/net
in
  your Linux system, then you could load module into system
by
  console command "insmod fealnx.o" and then "ifconfig eth0
up" to
 bring this adapter to work.

        You could use console command "linuxconf" to
configure
 this adapter card too.


     4. If your Linux kernel is any new version above than
2.4.5
  (included) and it is a new installation, you can configure
the
  kernel by following console commands to enable the driver
for
 SURECOM EP-320X-S/S-1 100/10M Ethernet PCI Adapter.

           #/usr/src/menuconfig

        Enable the option of "Myson MTD-8XX PCI Ethernet
support"
  in "Ethernet (10 or 100 M bit)" of "Network device support"
as a
 loadable module or system default module.

           #make dep

           #make clean

           #make bzImage

            #cp /usr/src/linux-2.4.X/arch/i386/boot/bzImage
/boot

        Then, edit /etc/lilo.conf, run "/sbin/lilo", and then
reboot
  your Linux system. After new kernel has been rebooted, it
will
 automatically load the driver for this adapter.


 Zna4i spored teb da si kompiliram failovete ot dir "2.2.x"
ni6to 4e kernela mi e po nov ?
 Iskam da te pitam sy6to ti pravil li si go tova i s kakyv
kernel si bil ?

Mnogo 10x x x 

 Digal sym go rychno na 2.2.x, a na po-nov na 2.4.13, kydeto
trqbvashe da e kato modul.

Znachi ako oshte ne si go pusnal toq tup surecom 
otiwash w /etc/rc.d/ i recaktirash rc.netdevice 
kato mu dobawqsh /sbin/modprobe fealnx 
az sum na slackware 8.1 i pri men  proraboti  
 two e obache ako go imash na modul, fealnx.o.gz mislq che
 beshe file-a za poweche infirmaciq man page-a na modeprobe
 tam ima opciq za list na wsichki moduli . ako imash problem
prati 1 mail na valkov@g00net.org