След като поставиш флашката,какво ти дават командите:
lsusb
dmesg
sabayon dimitar # lsusb
Bus 002 Device 002: ID 09da:055f A4 Tech Co., Ltd
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 004: ID 1516:1213 CompUSA
Bus 001 Device 003: ID 04f2:b071 Chicony Electronics Co., Ltd 2.0M UVC Webcam / CNF7129
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
sabayon dimitar # dmesg
0.349882] raid6: sse2x1 3250 MB/s
[ 0.366896] raid6: sse2x2 3394 MB/s
[ 0.366897] raid6: using algorithm sse2x2 (3394 MB/s)
[ 0.367031] ACPI: WMI: Mapper loaded
[ 0.367031] PCI: Using ACPI for IRQ routing
[ 0.367031] PCI: pci_cache_line_size set to 64 bytes
[ 0.367099] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
[ 0.367102] reserve RAM buffer: 000000007ffa8000 - 000000007fffffff
[ 0.367119] HPET: 4 timers in total, 0 timers will be used for per-cpu timer
[ 0.367119] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31, 31
[ 0.367119] hpet0: 4 comparators, 64-bit 25.000000 MHz counter
[ 0.370026] Switching to clocksource tsc
[ 0.372580] pnp: PnP ACPI init
[ 0.372588] ACPI: bus type pnp registered
[ 0.381149] pnp: PnP ACPI: found 14 devices
[ 0.381151] ACPI: ACPI bus type pnp unregistered
[ 0.381155] PnPBIOS: Disabled by ACPI PNP
[ 0.381167] system 00:06: [io 0x04d0-0x04d1] has been reserved
[ 0.381170] system 00:06: [io 0x0800-0x080f] has been reserved
[ 0.381173] system 00:06: [io 0x4000-0x407f] has been reserved
[ 0.381176] system 00:06: [io 0x4080-0x40ff] has been reserved
[ 0.381179] system 00:06: [io 0x4400-0x447f] has been reserved
[ 0.381183] system 00:06: [io 0x4480-0x44ff] has been reserved
[ 0.381186] system 00:06: [io 0x4800-0x487f] has been reserved
[ 0.381189] system 00:06: [io 0x4880-0x48ff] has been reserved
[ 0.381192] system 00:06: [mem 0x000d0000-0x000d3fff window] has been reserved
[ 0.381196] system 00:06: [mem 0x000d4000-0x000d7fff window] has been reserved
[ 0.381199] system 00:06: [mem 0x000de000-0x000dffff window] has been reserved
[ 0.381203] system 00:06: [mem 0xfefe2000-0xfefe3fff] has been reserved
[ 0.381206] system 00:06: [mem 0xfefe1000-0xfefe1fff] has been reserved
[ 0.381210] system 00:06: [mem 0xfee01000-0xfeefffff] has been reserved
[ 0.381213] system 00:06: [mem 0xfed01000-0xfed01fff] has been reserved
[ 0.381219] system 00:09: [io 0x0250-0x0253] has been reserved
[ 0.381222] system 00:09: [io 0x0256-0x025f] has been reserved
[ 0.381225] system 00:09: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.381228] system 00:09: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.381233] system 00:0a: [io 0x0260-0x026f] has been reserved
[ 0.381238] system 00:0b: [io 0x5000-0x507f] has been reserved
[ 0.381241] system 00:0b: [io 0x5080-0x50ff] has been reserved
[ 0.381246] system 00:0c: [mem 0xfc000000-0xfdffffff] has been reserved
[ 0.381251] system 00:0d: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.381254] system 00:0d: [mem 0x000c0000-0x000cffff] could not be reserved
[ 0.381257] system 00:0d: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.381260] system 00:0d: [mem 0x00100000-0x7fffffff] could not be reserved
[ 0.381263] system 00:0d: [mem 0xfc000000-0xffffffff] could not be reserved
[ 0.416095] pci 0000:00:09.0: PCI bridge to [bus 01-01]
[ 0.416098] pci 0000:00:09.0: bridge window [io disabled]
[ 0.416102] pci 0000:00:09.0: bridge window [mem disabled]
[ 0.416105] pci 0000:00:09.0: bridge window [mem pref disabled]
[ 0.416111] pci 0000:00:10.0: PCI bridge to [bus 02-02]
[ 0.416114] pci 0000:00:10.0: bridge window [io 0xd000-0xdfff]
[ 0.416118] pci 0000:00:10.0: bridge window [mem 0xfaf00000-0xfbffffff]
[ 0.416122] pci 0000:00:10.0: bridge window [mem 0xe0000000-0xf9ffffff 64bit pref]
[ 0.416127] pci 0000:00:15.0: PCI bridge to [bus 03-03]
[ 0.416132] pci 0000:00:15.0: bridge window [io 0xe000-0xefff]
[ 0.416142] pci 0000:00:15.0: bridge window [mem 0xfea00000-0xfeafffff]
[ 0.416150] pci 0000:00:15.0: bridge window [mem pref disabled]
[ 0.416164] pci 0000:00:16.0: PCI bridge to [bus 04-04]
[ 0.416165] pci 0000:00:16.0: bridge window [io disabled]
[ 0.416176] pci 0000:00:16.0: bridge window [mem 0xfeb00000-0xfebfffff]
[ 0.416183] pci 0000:00:16.0: bridge window [mem pref disabled]
[ 0.416202] pci 0000:00:09.0: setting latency timer to 64
[ 0.416209] pci 0000:00:10.0: setting latency timer to 64
[ 0.416675] ACPI: PCI Interrupt Link [LRP3] enabled at IRQ 23
[ 0.416678] alloc irq_desc for 23 on node -1
[ 0.416680] alloc kstat_irqs on node -1
[ 0.416685] pci 0000:00:15.0: PCI INT A -> Link[LRP3] -> GSI 23 (level, low) -> IRQ 23
[ 0.416694] pci 0000:00:15.0: setting latency timer to 64
[ 0.417161] ACPI: PCI Interrupt Link [LRP4] enabled at IRQ 22
[ 0.417164] alloc irq_desc for 22 on node -1
[ 0.417166] alloc kstat_irqs on node -1
[ 0.417170] pci 0000:00:16.0: PCI INT A -> Link[LRP4] -> GSI 22 (level, low) -> IRQ 22
[ 0.417179] pci 0000:00:16.0: setting latency timer to 64
[ 0.417185] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.417187] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.417190] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.417192] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
[ 0.417194] pci_bus 0000:00: resource 8 [mem 0x80000000-0xfbffffff]
[ 0.417197] pci_bus 0000:00: resource 9 [mem 0xfe000000-0xfebfffff]
[ 0.417199] pci_bus 0000:01: resource 4 [io 0x0000-0x0cf7]
[ 0.417201] pci_bus 0000:01: resource 5 [io 0x0d00-0xffff]
[ 0.417204] pci_bus 0000:01: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.417206] pci_bus 0000:01: resource 7 [mem 0x000d0000-0x000dffff]
[ 0.417208] pci_bus 0000:01: resource 8 [mem 0x80000000-0xfbffffff]
[ 0.417210] pci_bus 0000:01: resource 9 [mem 0xfe000000-0xfebfffff]
[ 0.417213] pci_bus 0000:02: resource 0 [io 0xd000-0xdfff]
[ 0.417215] pci_bus 0000:02: resource 1 [mem 0xfaf00000-0xfbffffff]
[ 0.417217] pci_bus 0000:02: resource 2 [mem 0xe0000000-0xf9ffffff 64bit pref]
[ 0.417220] pci_bus 0000:03: resource 0 [io 0xe000-0xefff]
[ 0.417222] pci_bus 0000:03: resource 1 [mem 0xfea00000-0xfeafffff]
[ 0.417224] pci_bus 0000:04: resource 1 [mem 0xfeb00000-0xfebfffff]
[ 0.417245] NET: Registered protocol family 2
[ 0.417277] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.417372] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.417818] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.418051] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.418053] TCP reno registered
[ 0.418056] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.418064] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.418136] NET: Registered protocol family 1
[ 0.418229] RPC: Registered udp transport module.
[ 0.418231] RPC: Registered tcp transport module.
[ 0.418233] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.451064] pci 0000:02:00.0: Boot video device
[ 0.451073] PCI: CLS 64 bytes, default 64
[ 0.451123] Trying to unpack rootfs image as initramfs...
[ 0.591337] Freeing initrd memory: 7808k freed
[ 0.596198] Simple Boot Flag at 0xef set to 0x1
[ 0.597141] audit: initializing netlink socket (disabled)
[ 0.597156] type=2000 audit(1319822993.595:1): initialized
[ 0.597295] highmem bounce pool size: 64 pages
[ 0.597300] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.599823] VFS: Disk quotas dquot_6.5.2
[ 0.599889] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.600617] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.601547] Installing knfsd (copyright (C) 1996
okir@monad.swb.de).
[ 0.602074] Registering the dns_resolver key type
[ 0.602083] Slow work thread pool: Starting up
[ 0.602109] Slow work thread pool: Ready
[ 0.602161] NTFS driver 2.1.29 [Flags: R/W].
[ 0.602330] ROMFS MTD (C) 2007 Red Hat, Inc.
[ 0.602432] QNX4 filesystem 0.2.3 registered.
[ 0.602472] fuse init (API version 7.14)
[ 0.602753] JFS: nTxBlock = 8192, nTxLock = 65536
[ 0.605859] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[ 0.606649] SGI XFS Quota Management subsystem
[ 0.606914] Btrfs loaded
[ 0.607168] aufs 2-35-rcN
[ 0.607174] msgmni has been set to 1715
[ 0.607583] alg: No test for stdrng (krng)
[ 0.607588] async_tx: api initialized (async)
[ 0.607644] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.607646] io scheduler noop registered
[ 0.607648] io scheduler deadline registered (default)
[ 0.607847] pcieport 0000:00:15.0: setting latency timer to 64
[ 0.607963] alloc irq_desc for 40 on node -1
[ 0.607965] alloc kstat_irqs on node -1
[ 0.607987] pcieport 0000:00:15.0: irq 40 for MSI/MSI-X
[ 0.608152] pcieport 0000:00:16.0: setting latency timer to 64
[ 0.608265] alloc irq_desc for 41 on node -1
[ 0.608266] alloc kstat_irqs on node -1
[ 0.608284] pcieport 0000:00:16.0: irq 41 for MSI/MSI-X
[ 0.633771] toshiba: not a supported Toshiba laptop
[ 0.633900] Linux agpgart interface v0.103
[ 0.634211] vesafb: framebuffer at 0xf9000000, mapped to 0xf8580000, using 1536k, total 1536k
[ 0.634214] vesafb: mode is 1024x768x16, linelength=2048, pages=0
[ 0.634216] vesafb: scrolling: redraw
[ 0.634219] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 0.646373] Console: switching to colour frame buffer device 128x48
[ 0.756433] fbcondecor: console 0 using theme 'sabayon'
[ 0.820247] fbcondecor: switched decor state to 'on' on console 0
[ 0.820942] fb0: VESA VGA frame buffer device
[ 0.821175] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.821181] ACPI: Power Button [PWRB]
[ 0.821245] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
[ 0.821249] ACPI: Sleep Button [SLPB]
[ 0.821312] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input2
[ 0.823734] ACPI: Lid Switch [LID]
[ 0.823817] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 0.823820] ACPI: Power Button [PWRF]
[ 0.823962] ACPI: acpi_idle registered with cpuidle
[ 0.824723] Monitor-Mwait will be used to enter C-1 state
[ 0.824739] Monitor-Mwait will be used to enter C-3 state
[ 0.824756] Monitor-Mwait will be used to enter C-3 state
[ 0.824766] Marking TSC unstable due to TSC halts in idle
[ 0.824812] Switching to clocksource hpet
[ 0.837558] thermal LNXTHERM:01: registered as thermal_zone0
[ 0.837568] ACPI: Thermal Zone [THRM] (52 C)
[ 0.837605] ERST: Table is not found!
[ 0.837614] isapnp: Scanning for PnP cards...
[ 1.150015] isapnp: No Plug & Play device found
[ 1.150019] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 4.161029] floppy0: no floppy controllers found
[ 4.162890] brd: module loaded
[ 4.163810] loop: module loaded
[ 4.163812] Compaq SMART2 Driver (v 2.6.0)
[ 4.163892] HP CISS Driver (v 3.6.20)
[ 4.164320] MM: desc_per_page = 128
[ 4.164558] Loading iSCSI transport class v2.0-870.
[ 4.165052] fnic: Cisco FCoE HBA Driver, ver 1.4.0.145
[ 4.166502] Loading Adaptec I2O RAID: Version 2.4 Build 5go
[ 4.166504] Detecting Adaptec I2O RAID controllers...
[ 4.166895] Adaptec aacraid driver 1.1-5[26400]-ms
[ 4.167154] aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
[ 4.167374] NCR53c406a: no available ports found
[ 4.167377] sym53c416.c: Version 1.0.0-ac
[ 4.167392] qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options
[ 4.167451] QLogic Fibre Channel HBA Driver: 8.03.02-k2
[ 4.167547] iscsi: registered transport (qla4xxx)
[ 4.167591] QLogic iSCSI HBA Driver
[ 4.167593] Emulex LightPulse Fibre Channel SCSI driver 8.3.12
[ 4.167595] Copyright(c) 2004-2009 Emulex. All rights reserved.
[ 4.189027] Failed initialization of WD-7000 SCSI card!
[ 4.532746] DC390: clustering now enabled by default. If you get problems load
[ 4.532748] with "disable_clustering=1" and report to maintainers
[ 4.532829] megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
[ 4.532892] megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
[ 4.532932] megasas: 00.00.04.17.1-rc1 Thu. Oct. 29, 11:41:51 PST 2009
[ 4.532975] mpt2sas version 05.100.00.02 loaded
[ 4.533116] GDT-HA: Storage RAID Controller Driver. Version: 3.05
[ 4.533245] 3ware Storage Controller device driver for Linux v1.26.02.003.
[ 4.533286] 3ware 9000 Storage Controller device driver for Linux v2.26.02.014.
[ 4.533330] LSI 3ware SAS/SATA-RAID Controller device driver for Linux v3.26.02.000.
[ 4.533375] nsp32: loading...
[ 4.533416] ipr: IBM Power RAID SCSI Device Driver version: 2.5.0 (February 11, 2010)
[ 4.533460] RocketRAID 3xxx/4xxx Controller driver v1.6 (090910)
[ 4.533502] stex: Promise SuperTrak EX Driver version: 4.6.0000.4
[ 4.533586] cxgb3i: tag itt 0x1fff, 13 bits, age 0xf, 4 bits.
[ 4.533627] iscsi: registered transport (cxgb3i)
[ 4.533631] Broadcom NetXtreme II iSCSI Driver bnx2i v2.1.1 (Mar 24, 2010)
[ 4.533672] iscsi: registered transport (bnx2i)
[ 4.533675] VMware PVSCSI driver - version 1.0.1.0-k
[ 4.533724] st: Version 20081215, fixed bufsize 32768, s/g segs 256
[ 4.533797] osst :I: Tape driver with OnStream support version 0.99.4
[ 4.533798] osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
[ 4.534048] ahci 0000:00:0b.0: version 3.0
[ 4.534536] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 5
[ 4.534546] ahci 0000:00:0b.0: PCI INT A -> Link[LSA0] -> GSI 5 (level, low) -> IRQ 5
[ 4.534582] alloc irq_desc for 42 on node -1
[ 4.534584] alloc kstat_irqs on node -1
[ 4.534592] ahci 0000:00:0b.0: irq 42 for MSI/MSI-X
[ 4.534599] ahci 0000:00:0b.0: controller can't do PMP, turning off CAP_PMP
[ 4.534637] ahci 0000:00:0b.0: AHCI 0001.0200 32 slots 2 ports 3 Gbps 0x3 impl IDE mode
[ 4.534641] ahci 0000:00:0b.0: flags: 64bit ncq sntf led pio slum part sxs
[ 4.534645] ahci 0000:00:0b.0: setting latency timer to 64
[ 4.534805] scsi2 : ahci
[ 4.534958] scsi3 : ahci
[ 4.535116] ata1: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 42
[ 4.535119] ata2: SATA max UDMA/133 irq_stat 0x00400000, PHY RDY changed irq 42
[ 4.537979] scsi4 : pata_legacy
[ 4.538087] ata3: PATA max PIO4 cmd 0x1f0 ctl 0x3f6 irq 14
[ 5.258021] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 5.258033] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 5.258903] ata2.00: ATAPI: Optiarc DVD RW AD-7590S, 1.00, max UDMA/100
[ 5.262023] ata2.00: configured for UDMA/100
[ 5.306205] ata1.00: ATA-8: ST9500325AS, 0002SDM1, max UDMA/133
[ 5.306208] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 5.308394] ata1.00: configured for UDMA/133
[ 5.308493] scsi 2:0:0:0: Direct-Access ATA ST9500325AS 0002 PQ: 0 ANSI: 5
[ 5.308698] sd 2:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 5.308740] sd 2:0:0:0: [sda] Write Protect is off
[ 5.308743] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.308761] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.308785] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 5.308906] sda:
[ 5.314384] scsi 3:0:0:0: CD-ROM Optiarc DVD RW AD-7590S 1.00 PQ: 0 ANSI: 5
[ 5.317872] sda1 sda2 sda3 sda4 <sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 5.335171] Uniform CD-ROM driver Revision: 3.20
[ 5.335301] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 5.335412] sr 3:0:0:0: Attached scsi generic sg1 type 5
[ 5.336152] sda5 sda6 sda7 sda8 >
[ 5.398896] sd 2:0:0:0: [sda] Attached SCSI disk
[ 5.399155] scsi5 : pata_legacy
[ 5.399252] ata4: PATA max PIO4 cmd 0x170 ctl 0x376 irq 15
[ 5.550487] cnic: Broadcom NetXtreme II CNIC Driver cnic v2.1.2 (May 26, 2010)
[ 5.550604] I2O subsystem v1.325
[ 5.550606] i2o: max drivers = 8
[ 5.550761] I2O Configuration OSM v1.323
[ 5.550858] I2O Bus Adapter OSM v1.317
[ 5.550894] I2O Block Device OSM v1.325
[ 5.551064] I2O SCSI Peripheral OSM v1.316
[ 5.551100] I2O ProcFS OSM v1.316
[ 5.551141] Fusion MPT base driver 3.04.15
[ 5.551143] Copyright (c) 1999-2008 LSI Corporation
[ 5.551148] Fusion MPT SPI Host driver 3.04.15
[ 5.551193] Fusion MPT FC Host driver 3.04.15
[ 5.551240] Fusion MPT SAS Host driver 3.04.15
[ 5.551286] Fusion MPT misc device (ioctl) driver 3.04.15
[ 5.551340] mptctl: Registered with Fusion MPT base driver
[ 5.551342] mptctl: /dev/mptctl @ (major,minor=10,220)
[ 5.551345] Fusion MPT LAN driver 3.04.15
[ 5.551428] usbmon: debugfs is not available
[ 5.551430] Initializing USB Mass Storage driver...
[ 5.551475] usbcore: registered new interface driver usb-storage
[ 5.551476] USB Mass Storage support registered.
[ 5.551518] usbcore: registered new interface driver libusual
[ 5.551557] usbcore: registered new interface driver ums-alauda
[ 5.551596] usbcore: registered new interface driver ums-cypress
[ 5.551634] usbcore: registered new interface driver ums-datafab
[ 5.551674] usbcore: registered new interface driver ums-freecom
[ 5.551712] usbcore: registered new interface driver ums-isd200
[ 5.551751] usbcore: registered new interface driver ums-jumpshot
[ 5.551790] usbcore: registered new interface driver ums-karma
[ 5.551829] usbcore: registered new interface driver ums-onetouch
[ 5.551868] usbcore: registered new interface driver ums-sddr09
[ 5.551908] usbcore: registered new interface driver ums-sddr55
[ 5.551947] usbcore: registered new interface driver ums-usbat
[ 5.552076] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[ 5.555826] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 5.558213] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 5.558219] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 5.558222] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 5.558224] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 5.558227] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 5.558461] mice: PS/2 mouse device common for all mice
[ 5.559112] rtc_cmos 00:08: RTC can wake from S4
[ 5.559187] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
[ 5.559236] rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
[ 5.559277] md: linear personality registered for level -1
[ 5.559279] md: raid0 personality registered for level 0
[ 5.559281] md: raid1 personality registered for level 1
[ 5.559283] md: raid10 personality registered for level 10
[ 5.559285] md: raid6 personality registered for level 6
[ 5.559287] md: raid5 personality registered for level 5
[ 5.559289] md: raid4 personality registered for level 4
[ 5.559291] md: multipath personality registered for level -4
[ 5.559293] md: faulty personality registered for level -5
[ 5.559559] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised:
dm-devel@redhat.com[ 5.559701] EDAC MC: Ver: 2.1.0 Sep 19 2010
[ 5.559959] EISA: Probing bus 0 at eisa.0
[ 5.559961] EISA: Cannot allocate resource for mainboard
[ 5.559964] Cannot allocate resource for EISA slot 1
[ 5.559966] Cannot allocate resource for EISA slot 2
[ 5.559967] Cannot allocate resource for EISA slot 3
[ 5.559969] Cannot allocate resource for EISA slot 4
[ 5.559971] Cannot allocate resource for EISA slot 5
[ 5.559973] Cannot allocate resource for EISA slot 6
[ 5.559975] Cannot allocate resource for EISA slot 7
[ 5.559977] Cannot allocate resource for EISA slot 8
[ 5.559978] EISA: Detected 0 cards.
[ 5.560388] cpuidle: using governor ladder
[ 5.560932] cpuidle: using governor menu
[ 5.561037] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[ 5.562370] usbcore: registered new interface driver hiddev
[ 5.562416] usbcore: registered new interface driver usbhid
[ 5.562418] usbhid: USB HID core driver
[ 5.562454] Asus Laptop ACPI Extras version 0.30
[ 5.568143] BSTS called, 0xef6b returned
[ 5.568146] unsupported model K50IN, trying default values
[ 5.568148] send /proc/acpi/dsdt to the developers
[ 5.568424] TCP bic registered
[ 5.568427] NET: Registered protocol family 17
[ 5.569685] Using IPI No-Shortcut mode
[ 5.569881] TuxOnIce 3.1.1.1 (
http://tuxonice.net)
[ 5.597601] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
[ 5.762796] TuxOnIce: Can't translate "UUID=873d0c1f-97d1-4e4c-b410-fdcffa28c4c1" into a device id yet.
[ 5.769165] registered taskstats version 1
[ 5.769563] rtc_cmos 00:08: setting system clock to 2011-10-28 17:29:59 UTC (1319822999)
[ 5.769660] Freeing unused kernel memory: 628k freed
[ 6.007712] psmouse serio4: ID: 10 00 64
[ 6.098552] elantech: assuming hardware version 2, firmware version 4.1.1
[ 6.133157] elantech: Synaptics capabilities query result 0x7e, 0x13, 0x0d.
[ 6.229477] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio4/input/input5
[ 6.358874] scsi: <fdomain> Detection failed (no card)
[ 6.394709] psmouse serio4: ID: 10 00 64
[ 6.420326] imm: Version 2.05 (for Linux 2.4.0)
[ 6.488868] elantech: assuming hardware version 2, firmware version 4.1.1
[ 6.503455] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.504020] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 21
[ 6.504025] alloc irq_desc for 21 on node -1
[ 6.504027] alloc kstat_irqs on node -1
[ 6.504034] ehci_hcd 0000:00:04.1: PCI INT B -> Link[LUB2] -> GSI 21 (level, low) -> IRQ 21
[ 6.504050] ehci_hcd 0000:00:04.1: setting latency timer to 64
[ 6.504053] ehci_hcd 0000:00:04.1: EHCI Host Controller
[ 6.504073] ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
[ 6.504094] ehci_hcd 0000:00:04.1: debug port 1
[ 6.504102] ehci_hcd 0000:00:04.1: cache line size of 64 is not supported
[ 6.504118] ehci_hcd 0000:00:04.1: irq 21, io mem 0xfae7ec00
[ 6.510086] ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00
[ 6.510469] hub 1-0:1.0: USB hub found
[ 6.510473] hub 1-0:1.0: 8 ports detected
[ 6.523924] elantech: Synaptics capabilities query result 0x7e, 0x13, 0x0d.
[ 6.536086] uhci_hcd: USB Universal Host Controller Interface driver
[ 6.557729] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.558263] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 20
[ 6.558267] alloc irq_desc for 20 on node -1
[ 6.558269] alloc kstat_irqs on node -1
[ 6.558276] ohci_hcd 0000:00:04.0: PCI INT A -> Link[LUB0] -> GSI 20 (level, low) -> IRQ 20
[ 6.558292] ohci_hcd 0000:00:04.0: setting latency timer to 64
[ 6.558295] ohci_hcd 0000:00:04.0: OHCI Host Controller
[ 6.558307] ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
[ 6.558333] ohci_hcd 0000:00:04.0: irq 20, io mem 0xfae7f000
[ 6.611370] hub 2-0:1.0: USB hub found
[ 6.611375] hub 2-0:1.0: 8 ports detected
[ 6.624515] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio4/input/input6
[ 6.634157] sl811: driver sl811-hcd, 19 May 2005
[ 6.708613] e1000: Intel(R) PRO/1000 Network Driver - version 7.3.21-k6-NAPI
[ 6.708616] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 6.757188] iscsi: registered transport (tcp)
[ 6.915024] usb 1-5: new high speed USB device using ehci_hcd and address 3
[ 7.337023] usb 2-2: new full speed USB device using ohci_hcd and address 2
[ 7.534610] input: A4TECH USB Device as /devices/pci0000:00/0000:00:04.0/usb2/2-2/2-2:1.0/input/input7
[ 7.535045] generic-usb 0003:09DA:055F.0001: input,hiddev0,hidraw0: USB HID v1.11 Keyboard [A4TECH USB Device] on usb-0000:00:04.0-2/input0
[ 7.540395] input: A4TECH USB Device as /devices/pci0000:00/0000:00:04.0/usb2/2-2/2-2:1.1/input/input8
[ 7.540769] generic-usb 0003:09DA:055F.0002: input,hidraw1: USB HID v1.11 Mouse [A4TECH USB Device] on usb-0000:00:04.0-2/input1
[ 9.689748] TuxOnIce: Can't translate "UUID=873d0c1f-97d1-4e4c-b410-fdcffa28c4c1" into a device id yet.
[ 9.797391] TuxOnIce: Can't translate "UUID=873d0c1f-97d1-4e4c-b410-fdcffa28c4c1" into a device id yet.
[ 9.801217] EXT3-fs (sda8): error: couldn't mount because of unsupported optional features (240)
[ 9.801518] EXT2-fs (sda8): error: couldn't mount because of unsupported optional features (240)
[ 9.844421] EXT4-fs (sda8): mounted filesystem with ordered data mode. Opts: (null)
[ 13.504638] <30>udev[4793]: starting version 167
[ 13.802751] ACPI: AC Adapter [AC0] (on-line)
[ 13.804025] ACPI: Battery Slot [BAT0] (battery absent)
[ 13.864024] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 13.864564] ACPI: PCI Interrupt Link [LN3A] enabled at IRQ 19
[ 13.864568] alloc irq_desc for 19 on node -1
[ 13.864570] alloc kstat_irqs on node -1
[ 13.864577] r8169 0000:03:00.0: PCI INT A -> Link[LN3A] -> GSI 19 (level, low) -> IRQ 19
[ 13.864619] r8169 0000:03:00.0: setting latency timer to 64
[ 13.864667] alloc irq_desc for 43 on node -1
[ 13.864669] alloc kstat_irqs on node -1
[ 13.864679] r8169 0000:03:00.0: irq 43 for MSI/MSI-X
[ 13.864844] r8169 0000:03:00.0: eth0: RTL8168b/8111b at 0xf8ada000, 90:e6:ba:30:6b:ad, XID 18000000 IRQ 43
[ 13.907945] i2c i2c-0: nForce2 SMBus adapter at 0x4d00
[ 13.907952] ACPI: resource nForce2_smbus [io 0x4e00-0x4e3f] conflicts with ACPI region SM00 [
0x00004e00-0x00004e3f flags 0x30]
[ 13.907955] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 13.930116] input: PC Speaker as /devices/platform/pcspkr/input/input9
[ 14.062132] cfg80211: Calling CRDA to update world regulatory domain
[ 14.083383] acpi device:23: registered as cooling_device2
[ 14.090159] acpi device:24: registered as cooling_device3
[ 14.090904] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/device:22/LNXVIDEO:00/input/input10
[ 14.090993] ACPI: Video Device [IGPU] (multi-head: yes rom: no post: no)
[ 14.144389] Linux video capture interface: v2.00
[ 14.172575] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 14.178907] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 14.295282] uvcvideo: Found UVC 1.00 device CNF7129 (04f2:b071)
[ 14.318055] input: CNF7129 as /devices/pci0000:00/0000:00:04.1/usb1/1-5/1-5:1.0/input/input11
[ 14.318108] usbcore: registered new interface driver uvcvideo
[ 14.318111] USB Video Class driver (v0.1.0)
[ 14.349156] HDA Intel 0000:00:08.0: power state changed by ACPI to D0
[ 14.349208] HDA Intel 0000:00:08.0: power state changed by ACPI to D0
[ 14.349676] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 23
[ 14.349680] HDA Intel 0000:00:08.0: PCI INT A -> Link[LAZA] -> GSI 23 (level, low) -> IRQ 23
[ 14.349684] hda_intel: Disable MSI for Nvidia chipset
[ 14.349722] HDA Intel 0000:00:08.0: setting latency timer to 64
[ 14.747077] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:08.0/input/input12
[ 14.785650] ACPI: PCI Interrupt Link [LN4A] enabled at IRQ 18
[ 14.785655] alloc irq_desc for 18 on node -1
[ 14.785657] alloc kstat_irqs on node -1
[ 14.785664] ath9k 0000:04:00.0: PCI INT A -> Link[LN4A] -> GSI 18 (level, low) -> IRQ 18
[ 14.785673] ath9k 0000:04:00.0: setting latency timer to 64
[ 14.835506] ath: EEPROM regdomain: 0x60
[ 14.835508] ath: EEPROM indicates we should expect a direct regpair map
[ 14.835512] ath: Country alpha2 being used: 00
[ 14.835514] ath: Regpair used: 0x60
[ 14.838298] phy0: Selected rate control algorithm 'ath9k_rate_control'
[ 14.838460] Registered led device: ath9k-phy0::radio
[ 14.838475] Registered led device: ath9k-phy0::assoc
[ 14.838489] Registered led device: ath9k-phy0::tx
[ 14.838503] Registered led device: ath9k-phy0::rx
[ 14.838509] phy0: Atheros AR9285 Rev:2 mem=0xf8e60000, irq=18
[ 15.550578] nvidia: module license 'NVIDIA' taints kernel.
[ 15.550582] Disabling lock debugging due to kernel taint
[ 16.557226] ACPI: PCI Interrupt Link [LPMU] enabled at IRQ 22
[ 16.557231] nvidia 0000:00:03.5: PCI INT B -> Link[LPMU] -> GSI 22 (level, low) -> IRQ 22
[ 16.557691] ACPI: PCI Interrupt Link [SGRU] enabled at IRQ 21
[ 16.557695] nvidia 0000:02:00.0: PCI INT A -> Link[SGRU] -> GSI 21 (level, low) -> IRQ 21
[ 16.557701] nvidia 0000:02:00.0: setting latency timer to 64
[ 16.557705] vgaarb: device changed decodes: PCI:0000:02:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 16.557982] NVRM: loading NVIDIA UNIX x86 Kernel Module 260.19.36 Tue Jan 18 17:10:40 PST 2011
[ 20.407527] EXT4-fs (sda8): re-mounted. Opts: (null)
[ 27.136919] r8169 0000:03:00.0: eth0: link down
[ 27.702733] fbcondecor: console 1 using theme 'sabayon'
[ 27.798593] fbcondecor: switched decor state to 'on' on console 1
[ 27.908577] fbcondecor: console 2 using theme 'sabayon'
[ 28.004453] fbcondecor: switched decor state to 'on' on console 2
[ 28.455581] fbcondecor: console 3 using theme 'sabayon'
[ 28.568318] fbcondecor: switched decor state to 'on' on console 3
[ 28.667910] fbcondecor: console 4 using theme 'sabayon'
[ 28.767297] fbcondecor: switched decor state to 'on' on console 4
[ 28.867354] fbcondecor: console 5 using theme 'sabayon'
[ 28.963785] fbcondecor: switched decor state to 'on' on console 5
[ 30.207564] NET: Registered protocol family 10
[ 30.207800] lo: Disabled Privacy Extensions
[ 30.207866] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 30.207908] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2770.307538] r8169 0000:03:00.0: eth0: link down
[ 2770.307698] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 2770.350026] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2771.575226] r8169 0000:03:00.0: eth0: link down
[ 2771.575383] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 2771.614249] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2899.600591] wlan0: authenticate with b0:48:7a:ac:63:d8 (try 1)
[ 2899.602749] wlan0: authenticated
[ 2899.602767] wlan0: associate with b0:48:7a:ac:63:d8 (try 1)
[ 2899.607311] wlan0: RX AssocResp from b0:48:7a:ac:63:d8 (capab=0x31 status=0 aid=2)
[ 2899.607316] wlan0: associated
[ 2899.613734] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 2907.982583] lo: Disabled Privacy Extensions
[ 2909.666085] wlan0: no IPv6 routers present
[ 2968.808021] usb 1-4: new high speed USB device using ehci_hcd and address 4
[ 2968.925055] scsi6 : usb-storage 1-4:1.0
[ 2969.927433] scsi 6:0:0:0: Direct-Access USB DISK 2.0 1.00 PQ: 0 ANSI: 2
[ 2969.928011] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 2969.930634] sd 6:0:0:0: [sdb] 16035840 512-byte logical blocks: (8.21 GB/7.64 GiB)
[ 2969.931300] sd 6:0:0:0: [sdb] Write Protect is off
[ 2969.931304] sd 6:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 2969.931306] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 2969.935291] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 2969.935297] sdb: sdb1
[ 2970.814282] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 2970.814286] sd 6:0:0:0: [sdb] Attached SCSI removable disk
Автор
Тема: Проблем с рачитане на флашка (Прочетена 1524 пъти)