Изпечатай

[LinuxuserX]

Здравейте,
на лаптопа ми от доста време като го стартирам трябва да въвеждам llformat за да ме пусне напред.

Ето информация от програмата :

Код:

ATA device, with non-removable media
	Model Number:       WDC WD3200BPVT-80JJ5T0                  
	Serial Number:      WD-WX81E71XUZ42
	Firmware Revision:  01.01A01
	Transport:          Serial, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6
Standards:
	Supported: 8 7 6 5 
	Likely used: 8
Configuration:
	Logical		max	current
	cylinders	16383	16383
	heads		16	16
	sectors/track	63	63
	--
	CHS current addressable sectors:   16514064
	LBA    user addressable sectors:  268435455
	LBA48  user addressable sectors:  625142448
	Logical  Sector size:                   512 bytes
	Physical Sector size:                  4096 bytes
	Logical Sector-0 offset:                  0 bytes
	device size with M = 1024*1024:      305245 MBytes
	device size with M = 1000*1000:      320072 MBytes (320 GB)
	cache/buffer size  = 8192 KBytes
	Nominal Media Rotation Rate: 5400
Capabilities:
	LBA, IORDY(can be disabled)
	Queue depth: 32
	Standby timer values: spec'd by Standard, with device specific minimum
	R/W multiple sector transfer: Max = 16	Current = 16
	Advanced power management level: 254
	DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 
	     Cycle time: min=120ns recommended=120ns
	PIO: pio0 pio1 pio2 pio3 pio4 
	     Cycle time: no flow control=120ns  IORDY flow control=120ns
Commands/features:
	Enabled	Supported:
	   *	SMART feature set
	   *	Security Mode feature set
	   *	Power Management feature set
	   *	Write cache
	   *	Look-ahead
	   *	Host Protected Area feature set
	   *	WRITE_BUFFER command
	   *	READ_BUFFER command
	   *	NOP cmd
	   *	DOWNLOAD_MICROCODE
	   *	Advanced Power Management feature set
	    	SET_MAX security extension
	   *	48-bit Address feature set
	   *	Device Configuration Overlay feature set
	   *	Mandatory FLUSH_CACHE
	   *	FLUSH_CACHE_EXT
	   *	SMART error logging
	   *	SMART self-test
	   *	General Purpose Logging feature set
	   *	64-bit World wide name
	   *	IDLE_IMMEDIATE with UNLOAD
	   *	{READ,WRITE}_DMA_EXT_GPL commands
	   *	Segmented DOWNLOAD_MICROCODE
	   *	Gen1 signaling speed (1.5Gb/s)
	   *	Gen2 signaling speed (3.0Gb/s)
	   *	Native Command Queueing (NCQ)
	   *	Host-initiated interface power management
	   *	Phy event counters
	   *	Idle-Unload when NCQ is active
	   *	NCQ priority information
	   *	DMA Setup Auto-Activate optimization
	    	Device-initiated interface power management
	   *	Software settings preservation
	   *	SMART Command Transport (SCT) feature set
	   *	SCT Write Same (AC2)
	   *	SCT Features Control (AC4)
	   *	SCT Data Tables (AC5)
	    	unknown 206[12] (vendor specific)
	    	unknown 206[13] (vendor specific)
	    	unknown 206[14] (vendor specific)
Security: 
	Master password revision code = 1
		supported
		enabled
	not	locked
		frozen
	not	expired: security count
		supported: enhanced erase
	Security level high
	70min for SECURITY ERASE UNIT. 70min for ENHANCED SECURITY ERASE UNIT. 
Logical Unit WWN Device Identifier: 50014ee601f1a7f7
	NAA		: 5
	IEEE OUI	: 0014ee
	Unique ID	: 601f1a7f7
Checksum: correct

Предполагам първо ми трябва Suspend. После с коя команда да я премахна ?

Linux Mint 18

Мерси!

[10101]

root@thinkpad:~# hdparm --Istdout /dev/sdb > sdb.ata_identify
root@thinkpad:~# P="$(ruby pw.rb sdb.ata_identify)"
Enter password: <<interactively asks for password>>
root@thinkpad:~# hdparm --security-disable $P /dev/sdb
security_password="GARBAGE"

/dev/sdb:
Issuing SECURITY_DISABLE command, password="GARBAGE", user=user


Now, hdparm -I gives me the following:

Code:
Security:
   Master password revision code = 16385
      supported
   not   enabled
   not   locked
   not   frozen
   not   expired: security count
      supported: enhanced erase
   94min for SECURITY ERASE UNIT. 94min for ENHANCED SECURITY ERASE UNIT.


https://forum.hddguru.com/viewtopic.php?f=1&t=32046

[LinuxuserX]

Здравейте,
при мен дискът е монтиран на /dev/sda1

Да заменя ли dev/sdb с dev/sda1 ?

Това просто ще махне паролата без да трие данни или ?

[LinuxuserX]

UP ?